CRL Profilé de porte effilé, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'épaisseur, plaque de 242 mm (9-1/2 po), acier inoxydable brossé - DR4TBS38P
Our innovative glass entrance system, the CRL Wedge-Lock Door Rail System features the exclusive CRL Wedge-Lock Securing System (U.S. Patents 6,434,905 and 6,912,818 B2, Canadian Patent 2,419,706, and European Patent No. EP 1 404 939 B1). A totally new concept for securing the glass in the door rail. It works by applying pressure from the bottom of the door rail, using two glass retaining aluminum extrusions via a flat stainless steel bar. As this bar is pulled down with socket head cap bolts, pressure is applied to the glass retaining aluminum extrusions. The bottom of the extrusions are at an angle and fit into an angled groove in the door rail. As the glass retaining extrusions are being pulled down, the angled wedge in the door rail also pulls the glass retaining extrusions together. This action, along with our specially designed door retaining gasket, creates a tremendous amount of force (more than 900 lbs.) in our 9" (228.6 mm) Corner Rail. That's 100 lbs. per inch. Imagine how much force is created in our full length 35-3/4" (908 mm) Door Rails!
Système exclusif de verrouillage Wedge-Lock CRL pour vitrage à sec, pour une installation rapide et une résistance élevée
Conçu pour des portes n'excédant pas 1,07 m (37 po) de large
Disponible uniquement sur commande
Système exclusif de verrouillage Wedge-Lock CRL pour vitrage à sec, pour une installation rapide et une résistance élevée
Conçu pour des portes n'excédant pas 1,07 m (37 po) de large
Disponible uniquement sur commande
Numro d'article: DR4TBS38P
galement disponible dans ces trois catalogues:
CRL63A Architectural Hardware Master, PAGE 125H
CRL14D Door and Entrance Catalog, PAGE 131D
AH18 Catalogue des mtaux architectur 2018, PAGE 139Z
HR18 Systmes de garde-corps d'architecture 2018, PAGE 508B
CRL93A Architectural Hardware, PAGE CH022
Couleur: Acier inoxydable bross
Expdier par: Expdition UPS
Poids d'expdition: 5 lb (2,27kg)
Commande minimum: 1 Unit
galement disponible dans ces trois catalogues:
CRL63A Architectural Hardware Master, PAGE 125H
CRL14D Door and Entrance Catalog, PAGE 131D
AH18 Catalogue des mtaux architectur 2018, PAGE 139Z
HR18 Systmes de garde-corps d'architecture 2018, PAGE 508B
CRL93A Architectural Hardware, PAGE CH022
Couleur: Acier inoxydable bross
Expdier par: Expdition UPS
Poids d'expdition: 5 lb (2,27kg)
Commande minimum: 1 Unit
NUMRO D'ARTICLE DESCRIPTION COULEUR
DR4TBL38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), pulvrisation noire
DR4TBS38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), acier inoxydable bross
DR4TDU38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, longueur de 241 mm (9-1/2 po), bronze anodis noir
DR4TPB38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), laiton poli
DR4TPS38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, longueur de 10,8 (35-1/2 po), acier inoxydable poli
DR4TSA38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), anodis satin
DR4TBL38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), pulvrisation noire
DR4TBS38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), acier inoxydable bross
DR4TDU38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, longueur de 241 mm (9-1/2 po), bronze anodis noir
DR4TPB38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), laiton poli
DR4TPS38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, longueur de 10,8 (35-1/2 po), acier inoxydable poli
DR4TSA38P CRL Profil de porte effil, sans serrure, 102 mm (4 po), verre de 9,5 mm (3/8 po) d'paisseur, plaque de 242 mm (9-1/2 po), anodis satin
The Wedge-Lock Glass Securing System gives you more than a secure attachment to the glass. It provides the fastest installation time of any door rail system offered to the industry. Experienced installers can have a door prepared for installation in less than ten minutes.
CRL Wedge-Lock Door Rails come completely fabricated and ready-to-install right out of the carton with the End Caps installed. After the rail is installed, the only thing required before hanging the door is to attach the door arm or pivot (not included) to the adjustable door alignment slide already assembled in the Door Rail. The Adjustable Door Alignment System feature allows you to adjust the door 1/8" (3.2 mm) toward or away from the jamb without removing the door. This is standard on both top and bottom rails.
After the door is installed all you need do to adjust the door is to remove the End Cap. This will reveal three socket head cap bolts. The center bolt is the securing bolt used to lock the adjustable slide in position. The two outer bolts are used to adjust the slide 1/8" (3.2 mm) in or out. The low profile of the adjustable slide allows the pivots with slotted grooves to be moved to a position other than the American Standard Setback of 2-3/4" (69.8 mm). This means we can fabricate them for vertically out-of-square openings.
Other reasons to choose Wedge-Lock Door Rails: Models are available to accept 3/8" to 3/4" (10 or 19 mm) glass; a rigid single component housing that will not shift and fall out of adjustment over time because it is not made up of two halves; the internal components do not require removal before installation; the glass securing pads are designed for longevity in extreme environments.
NOTE: All Wedge-Lock Door Rails feature the built-in Jamb Alignment Block, but arms and pivots must be ordered separately to meet job requirements.
CRL Wedge-Lock Door Rails come in several standard finishes, and can be quoted in custom finishes and widths upon request. Rail Specifications, Templates and Hardware Packages are available from CRL Technical Sales e-mail.
ORDERING INFORMATION:
All Door Rails are supplied with standard Kwik-Adjust Pivot Alignment System. Closer Arms and Floor or Overhead Pivots must be ordered separately.
Models with Locks are supplied with the Lock Mechanism installed. Matching finish Keyed Cylinders or Thumbturns must be ordered separately.
End Caps are included in the stock Door Rail lengths below. Door Rail length (including End Caps) must be specified when ordering Custom Length Rails.
CRL Wedge-Lock Door Rails come completely fabricated and ready-to-install right out of the carton with the End Caps installed. After the rail is installed, the only thing required before hanging the door is to attach the door arm or pivot (not included) to the adjustable door alignment slide already assembled in the Door Rail. The Adjustable Door Alignment System feature allows you to adjust the door 1/8" (3.2 mm) toward or away from the jamb without removing the door. This is standard on both top and bottom rails.
After the door is installed all you need do to adjust the door is to remove the End Cap. This will reveal three socket head cap bolts. The center bolt is the securing bolt used to lock the adjustable slide in position. The two outer bolts are used to adjust the slide 1/8" (3.2 mm) in or out. The low profile of the adjustable slide allows the pivots with slotted grooves to be moved to a position other than the American Standard Setback of 2-3/4" (69.8 mm). This means we can fabricate them for vertically out-of-square openings.
Other reasons to choose Wedge-Lock Door Rails: Models are available to accept 3/8" to 3/4" (10 or 19 mm) glass; a rigid single component housing that will not shift and fall out of adjustment over time because it is not made up of two halves; the internal components do not require removal before installation; the glass securing pads are designed for longevity in extreme environments.
NOTE: All Wedge-Lock Door Rails feature the built-in Jamb Alignment Block, but arms and pivots must be ordered separately to meet job requirements.
CRL Wedge-Lock Door Rails come in several standard finishes, and can be quoted in custom finishes and widths upon request. Rail Specifications, Templates and Hardware Packages are available from CRL Technical Sales e-mail.
ORDERING INFORMATION:
All Door Rails are supplied with standard Kwik-Adjust Pivot Alignment System. Closer Arms and Floor or Overhead Pivots must be ordered separately.
Models with Locks are supplied with the Lock Mechanism installed. Matching finish Keyed Cylinders or Thumbturns must be ordered separately.
End Caps are included in the stock Door Rail lengths below. Door Rail length (including End Caps) must be specified when ordering Custom Length Rails.
La plupart des poids d'expdition sont approximatifs et n'ont pas t vrifis. Si vous avez besoin du poids exact pour calculer le cot de l'expdition et ce cot est ncessaire pour complter la commande, veuillez l'obtenir avant de soumettre votre demande en prenant le contact avec le service client Glass Experts. Les images des produits proviennent des produits actuels ou proches. Couleurs peuvent varier selon la carte vido de votre ordinateur et selon le rglage des color de votre cran.
Références spécifiques